The DTR180ZK enables fast and efficient application of rebar tie wire, reducing the need for GC07 Hot-work permits and reliance on manual labour. The DTR180ZK delivers double loop ties at the press of a button and is ideal for time consuming construction tasks like laying concrete foundations over a wide area. It can be used one handed in either single or continuous mode, leaving the other hand free to adjust the position of the rebar. The tool is suitable for use with D10, D13 and D16 rebar in varying combinations of 2, 3 and 4 pieces. In continuous mode the operator can make multiple ties simply by pushing the contact arm against the workpieces while holding the trigger down. According to the condition of the tying material, the tying strength can be adjusted in six stages. Using a 5.0ah 18v battery, up to 120 ties of 0.8mm diameter annealed wire can be accomplished. The DTR180ZK does not produce heat or sparks, therefore operators do not need a GC07 permit to use it. Features & Benefits • Enables automatic & time saving rebar tying • Brushless • Onboard storage for hex key • Ergonomic softgrip handle • Single handed operation • Single or continuous operation modes • Tie wire reel replaced by opening the reel cover • Six stage tying strength adjustment Specifications • Battery Voltage: 14.4v/18v • Battery Type: Makita Li-ion • Tie Wire: 0.8mm • Applicable Rebar: D10 x D10 - (D13 x2) x (D13 x2) • Approximate Ties per Reel: 120 (with BL1850B Battery) • Net weight: 2.3-2.6kg • Vibration no load: 2.5m/sec² • Vibration K factor: 1.5m/sec² • Noise sound pressure: 78dB(A) • Noise K factor: 3dB(A) Contents • DTR180ZK Cordless Rebar Tying Tool • Hex Key • Belt Clip • Carry Case • No Battery • No Charger

Makita's DTW180 is a 3/8" square drive impact wrench which is powered by lithium ion power tool batteries from the 18v LXT cordless platform. One of its distinguishing features is a reverse rotation auto stop mode. This mode works only when pulling the trigger fully in counter-clockwise rotation. When the bolt/nut gets loosened enough, the tool stops the impact and rotation in 0.2 seconds. Features and Benefits • Electric brake • Variable speed control by trigger • Forward / reverse rotation • LED job light • Brushless motor • Ergonomic soft grip • Reverse rotation auto stop mode brakes tool rapidly in 0.2 seconds • 2-stage impact power selection • Compact & lightweight Specifications • Battery Type: Makita LXT Lithium-ion • Battery Voltage: 18v • Nut Busting Torque: 310 Nm • Drive Shank: 3/8" Square • Blows per Minute (Hi): 0 - 3,600 ipm • Blows per Minute (Lo): 0 - 2,000 ipm • Standard Bolt: M8-M16 • High Tensile Bolt: M6-M12 • Noise Sound Pressure: 89 dB(A) • Noise Sound Power: 100 dB(A) • Noise K Factor: 3 dB(A) • No Load Speed (Hi): 0 - 2,400 rpm • No Load Speed (Lo): 0 - 1,300 rpm • Max Fastening Torque: 180 Nm • Vibration: Fastening Bolt: 9.0 m/sec² • Vibration K Factor: 1.5 m/sec² • Net Weight: 1.2-1.5 kg Contents • Makita DTW180 18v LXT Cordless Brushless 3/8" Drive Impact Wrench • Belt Clip • No Batteries • No Charger • No Case

Makita's LS1219 is a sliding compound mitre saw with a 305mm blade. The motor head slides on fixed pipes without extending to the rear of the saw, allowing the machine to be placed close to the wall. Specifications • Blade Diameter: 305mm • Max mitre range: 60 - 60 ° • Max mitre cut at 90°: 92 x 382 mm • Bore Diameter: 30 mm • Max bevel range: 48 - 48° • Noise sound pressure: 91 dB(A) • Noise sound power: 100 dB(A) • Noise K factor: 3 dB(A) • Input Wattage (110v): 1,450 w • No Load Speed: 3200 rpm • Vibration K factor: 1.5 m/sec² • Vibration no load: 2.5 m/sec² • Net weight: 29.3 kg Features and Benefits • Motor head slides on fixed pipes without extending machine at rear end • Machine can be placed close to walls and other obstacles • Front knob for easy bevel adjustment • Holders to support a wide workpiece • Easy-to-operate mitre angle lock • One-touch sliding lock • Large turn base • Can be connected to dust extractor • Electric brake • Soft start • Constant speed control • Double Insulated Contents • LS1219 110v mitre saw • TCT saw blade • Dust bag • Triangular rule • Vertical vice • Hex wrench

Makita's LS1219 is a sliding compound mitre saw with a 305mm blade. The motor head slides on fixed pipes without extending to the rear of the saw, allowing the machine to be placed close to the wall. Specifications • Blade Diameter: 305mm • Max mitre range: 60 - 60 ° • Max mitre cut at 90°: 92 x 382 mm • Bore Diameter: 30 mm • Max bevel range: 48 - 48° • Noise sound pressure: 91 dB(A) • Noise sound power: 100 dB(A) • Noise K factor: 3 dB(A) • Input Wattage (240v): 1,800 w • No Load Speed: 3200 rpm • Vibration K factor: 1.5 m/sec² • Vibration no load: 2.5 m/sec² • Net weight: 29.3 kg Features and Benefits • Motor head slides on fixed pipes without extending machine at rear end • Machine can be placed close to walls and other obstacles • Front knob for easy bevel adjustment • Holders to support a wide workpiece • Easy-to-operate mitre angle lock • One-touch sliding lock • Large turn base • Can be connected to dust extractor • Electric brake • Soft start • Constant speed control • Double Insulated Contents • LS1219 240v mitre saw • TCT saw blade • Dust bag • Triangular rule • Vertical vice • Hex wrench

The LS1219L is a Sliding Compound Mitre Saw which is fitted with a 305mm blade. The motor head slides on fixed pipes without extending to the rear of the machine, allowing the LS1219L to be placed close to the wall. The LS1219L is the same as the LS1219 except the 'L' model has an additional laser guide for rapid setups. Specifications • Blade Diameter: 305mm • Max mitre range: 60 - 60 º • Max mitre cut at 90º: 92 x 382 mm • Bore Diameter: 30mm • Max bevel range: 48 - 48 º • Noise sound pressure: 91 dB(A) • Noise sound power: 100 dB(A) • Noise K factor: 3 dB(A) • Input Wattage (110v): 1,450 w • No Load Speed: 3200 rpm • Vibration K factor: 1.5 m/sec² • Vibration no load: 2.5 m/sec² • Net weight: 29.5 kg Features and Benefits • Built in laser guide • Motor head slides on fixed pipes without extending machine at rear end, so the machine can be placed close to wall • Front knob for easy bevel adjustment • Holders to support a wide workpiece • Easy-to-operate mitre angle lock • One-touch sliding lock • Large turn base • Connects to dust extractor • Electric brake • Soft start • Constant speed control • Double Insulated Contents • LS1219L 110v Sliding Compound Mitre Saw • TCT saw blade • Dust bag • Triangular rule • Vertical vice • Hex wrench

The LS1219L is a Sliding Compound Mitre Saw which is fitted with a 305mm blade. The motor head slides on fixed pipes without extending to the rear of the machine, allowing the LS1219L to be placed close to the wall. The LS1219L is the same as the LS1219 except the 'L' model has an additional laser guide for rapid setups. Specifications • Blade Diameter: 305mm • Max mitre range: 60 - 60 º • Max mitre cut at 90º: 92 x 382 mm • Bore Diameter: 30mm • Max bevel range: 48 - 48 º • Noise sound pressure: 91 dB(A) • Noise sound power: 100 dB(A) • Noise K factor: 3 dB(A) • Input Wattage (240v): 1,800 w • No Load Speed: 3200 rpm • Vibration K factor: 1.5 m/sec² • Vibration no load: 2.5 m/sec² • Net weight: 29.5 kg Features and Benefits • Built in laser guide • Motor head slides on fixed pipes without extending machine at rear end, so the machine can be placed close to wall • Front knob for easy bevel adjustment • Holders to support a wide workpiece • Easy-to-operate mitre angle lock • One-touch sliding lock • Large turn base • Connects to dust extractor • Electric brake • Soft start • Constant speed control • Double Insulated Contents • LS1219L 240v Sliding Compound Mitre Saw • TCT saw blade • Dust bag • Triangular rule • Vertical vice • Hex wrench

The SK105D is a cross line laser level which is primarily designed to be used with a Makita 12v Max CXT power tool battery. Specifications &bull; Battery Voltage: 12v &bull; Battery Type: Makita CXT Lithium Ion &bull; Laser Colour: Red &bull; Beam Direction / Fan Angle: Vertical >160&deg;, Horizontal >180&deg; &bull; Range: 25m &bull; Range with Receiver: 80m &bull; Self Levelling Accuracy: ±0.3 mm/m (= ±3.0 mm @ 10m) &bull; Horizontal / Vertical Line Accuracy: ±0.3 mm/m &bull; Self Levelling Range :± 4&deg; &bull; Self Levelling Time: < 3 Seconds &bull; Laser Type: 635 ± 5 nm, Class 2 &bull; Laser Line Width @ 5m:

The SK105GD is a cross line green laser level which is primarily designed to be used with a Makita 12v Max CXT power tool battery. Specifications &bull; Battery Voltage: 12v &bull; Battery Type: Makita CXT Lithium Ion &bull; Laser Colour: Green &bull; Beam Direction / Fan Angle: Vertical >160&deg;, Horizontal >180&deg; &bull; Range: 35m &bull; Range with Receiver: 80m &bull; Self levelling Accuracy: ±0.3 mm/m (= ±3.0 mm @ 10m) &bull; Horizontal / Vertical Line Accuracy: ±0.3 mm/m &bull; Self Levelling Range: ± 4&deg; &bull; Self Levelling Time:

Makita's DBN600ZJ is a cordless finishing nailer which is powered by a standard Makita 18v Li-ion LXT power tool battery (not included). Specifications &bull; Battery Type: Makita LXT Lithium-ion &bull; Battery Voltage: 18v &bull; Nail gauge: 16 Ga &bull; Nail Length: 25-64 mm &bull; Nail type: Finish &bull; Magazine Capacity: 110 &bull; Approximate shots per 4.0ah battery: 800 &bull; Noise sound pressure: 89 dB(A) &bull; Noise sound power: 100 dB(A) &bull; Noise K factor: 3 dB(A) &bull; Vibration K factor: 1.5 m/sec² &bull; Vibration no load: 2.5 m/sec² &bull; Net weight: 3.4 - 3.8 kg Features and Benefits &bull; Cordless nail gun for finishing applications &bull; Anti Dry-Fire Mechanism &bull; Rocker switch to select sequential / bump fire mode &bull; Tool-less depth adjustment &bull; Tool-less nail jam clearing &bull; Ergonomic soft grip &bull; LED job light &bull; Body bumper protects workpiece from scratches / damage &bull; Window to check qty of remaining nails Contents &bull; DBN600ZJ 18v Cordless Finishing Nailer &bull; Type 4 Makpac Connector Case &bull; Nose Adaptor &bull; Belt Clip &bull; No Batteries &bull; No Charger

Makita's CXT range expands the ever growing 10.8v power tool market with a selection of compact and lightweight machines which use a sliding lithium ion battery format. Utilising technology inherited from Makita's 18v range, these new batteries are equipped with overload protection circuitry and high capacity cells; fitted with multi-contact terminals to ensure stable connection even under extreme work vibration conditions, they are built for structural strength and durability and can be used in temperatures down to -20&deg;C. The JR103D is a higly manouevrable cordless reciprocating saw equipped with a dual trigger switch system for comfortable operation in multiple positions. It has a tool free blade clamp for quick & easy accessory changes and features an LED joblight for optimum visibility of the work area. Features & Benefits &bull; Slide type battery &bull; Tool free blade clamp &bull; Variable speed control triggers &bull; Paddle switch on tool body and trigger switch on handle &bull; Lock-off function &bull; LED job light &bull; Electric brake &bull; Shoe Adjustment &bull; Battery protection circuit &bull; High power &bull; Ergonomic handle for comfortable grip Specifications &bull; Battery Type: Li-ion &bull; Battery Voltage: 10.8v &bull; Capacity in Wood: 50mm &bull; Capacity in Mild Steel Pipe: 50mm &bull; Stroke Length: 13mm &bull; Noise Sound Pressure: 78dB(A) &bull; Noise K Factor: 3dB(A) &bull; No Load Speed: 0-3,300spm &bull; Variable Speed: Either Trigger &bull; Vibration K Factor: 1.5m/sec&sup2; &bull; Vibration Cutting Chipboard: 8.0m/sec&sup2; &bull; Net Weight: 1.5kg Contents &bull; Makita JR103D 12v Max CXT Cordless Reciprocating Saw &bull; Hex Wrench &bull; Recip Blades (x2) &bull; Makita BL1021B 12v CXT Cordless Li-ion 2ah Battery (x2) &bull; Makita DC10WD 12v CXT Battery Charger &bull; 821662-9 Plastic Carrying Case

Makita guide rail suitable for Makita Plunge saws, circular saws, jigsaws and routers. Equipped with anti-slip strips on the underside and top running strips for a smooth guide. Manufactured from extruded aluminium. Specifications &bull; Length: 1000mm &bull; Model: SP6000 Features and Benefits &bull; Replaceable splinter guard &bull; Anti-slip strips on the underside &bull; Top running strips for a smooth guide &bull; Can be paired with another guide rail with connector (not included) &bull; Suitable for Makita Plunge saws, circular saws, jigsaws and routers

We currently have no further description for this item or it does not need any further details. If this product has recently been added we will be working hard to get more information added as soon as possible.